Physical Quantities and Measurement Techniques · Cambridge syllabus 1.1 · Lesson 3 of 4
Measuring Time
Reaction time affects starting and stopping a stopwatch. Timing many repeats of a regular motion makes the total interval larger relative to this uncertainty. Divide the total time by the number of cycles to obtain one period.
By the end, you can
- Use clocks, stopwatches and electronic timers.
- Measure time intervals.
- Repeat measurements and calculate an average.
- Recognise sources of random and systematic uncertainty.
Time measurements
A stopwatch is only as good as the person pressing it. Human reaction time is roughly 0.2 s, and it enters the measurement twice — once when you start, once when you stop. Timing a single swing of a pendulum that lasts 1.5 s therefore carries an uncertainty of a similar size to a quarter of the thing you are measuring, which is useless.
The fix is to time many repeats and divide. Time twenty complete swings, get 32.0 s, and one period is 32.0 ÷ 20 = 1.60 s. The reaction-time error is still about 0.2 s, but now it sits against 32 s rather than 1.6 s, so as a fraction of the measurement it has shrunk by a factor of twenty. This is the single most useful experimental trick in the whole course, and it works for anything repetitive.
Repeating and averaging deals with random errors — the scatter that pushes readings above and below the true value unpredictably. It does nothing at all about a systematic error, which shifts every reading the same way: a stopwatch that runs slow, or a timer started at the wrong point in the swing. Averaging a hundred readings from a slow clock gives you a very precise wrong answer. Systematic errors have to be found and removed, usually by checking the instrument against a known standard. Electronic timing with light gates avoids reaction time altogether, which is why it is used where the interval is short.
Worth remembering
- Time n repeats and divide by n: the reaction-time uncertainty becomes a smaller fraction of the total.
- Random error → scatter; reduced by repeating and averaging.
- Systematic error → every reading shifted the same way; averaging does not help.
Worked example
Twenty oscillations take 32.0 s: period = 32.0 ÷ 20 = 1.60 s. A 0.2 s timing uncertainty is a smaller fraction of 32 s than of 1.6 s.
Investigate scatter and systematic error
Change a value and watch the readings follow. Open it on the lab stage
Investigate scatter and systematic error
There is no zero offset, and the readings lie up to 0.484 cm from the best-fit line.
- Furthest point from the best-fit line
- 0.484 cm
- 3.13 cm − 2.646 cm at 1 s
- Best-fit intercept
- 1.165 cm
- 1 cm true + 0 cm offset + 0.165 cm random
- Best-fit gradient
- 1.965 cm/s
- (20.815 cm − 1.165 cm) ÷ 10 s
Goal
Find out how random scatter and a zero offset each change a set of readings, and which of them taking more repeats can fix.
Predict, where you are
If Ithe, thewill
Say what you expect before you move anything. Check makes the change for you.
Test, still to come
Change one thing at a time and watch the readings. The notebook keeps a reading each time you record one.
Explain, still to come
After you check a prediction, this says why it happened.
Try this · 0 of 3
- Turn the random scatter up to 1.5 cm with no zero offset. Does the best-fit line still follow the true line?, not yet
- Set a zero offset of −1 cm with no scatter. How far does every reading move?, not yet
- With 1 cm of scatter and a 1 cm zero offset, take 10 repeats at each time. Which error does averaging reduce, and which does it leave?, not yet
reading = true value + zero offset + random error
at 5 s: 11 cm + 0 cm − 0.229 cm = 10.771 cm
Investigation notebook · 0 readings
Change one variable at a time and record the results. These readings stay here until you leave this lesson or reset the notebook.
About this model
Made-up readings of a distance that truly grows as 2 cm/s × time + 1 cm. Each reading’s random error comes from a fixed set drawn once, up to the scatter either side, so the same settings always give the same readings. The best-fit line is the least-squares straight line through the plotted points.
Practice
Warm-up · not marked
Check your understanding
Answer in your own words, then compare with the worked answer. Nothing here is saved or scored.
Worked answer
Mean total time = 15.3 s. Period = 15.3 ÷ 10 = 1.53 s.
Check your method, units and explanation against it.
Marked practice
Set 1 of 4 · easiest first · Checked as you go, with the worked answer. Sign in or create a free account to save your progress.