Thermal Properties and Temperature · Cambridge syllabus 2.2 · Lesson 2 of 3
Specific Heat Capacity
Includes Supplement objectivesA rise in temperature increases the internal energy of an object. Specific heat capacity c is the energy needed per kilogram per degree temperature rise: c = ΔE ÷ (mΔθ), so ΔE = mcΔθ. A higher c means more energy is required for the same mass and temperature change. Insulation reduces energy lost to surroundings.
By the end, you can
- Understand specific heat capacity as energy required per unit mass per degree temperature rise. [Supplement]
- Use energy = mass × specific heat capacity × temperature change. [Supplement]
- Measure energy supplied electrically. [Supplement]
- Measure mass and temperature change. [Supplement]
- Calculate specific heat capacity. [Supplement]
- Identify heat losses and experimental limitations. [Supplement]
- Know that a rise in the temperature of an object increases its internal energy.
- Describe a rise in temperature as an increase in the average kinetic energy of all the particles in the object. [Supplement]
Thermal energy
Different substances need different amounts of energy to warm up by the same amount. The specific heat capacity, c, of a substance is the energy needed per unit mass per unit rise in temperature: the energy needed to warm 1 kg of it by 1 °C. Its unit is the joule per kilogram per degree Celsius, J/(kg °C). It can also be given per gram, in J/(g °C), so water’s 4200 J/(kg °C) is the same as 4.2 J/(g °C).
The equation is written with c as the subject: c = ΔE ÷ (mΔθ), where ΔE is the energy transferred, m is the mass and Δθ is the temperature change. Rearranged, ΔE = mcΔθ. To warm 2 kg of water by 30 °C, with c = 4200 J/(kg °C), takes 2 × 4200 × 30 = 252 000 J. Working the other way, a 2 kg block that receives 9000 J and warms by 10 °C has c = 9000 ÷ (2 × 10) = 450 J/(kg °C). Δθ is the change in temperature, final minus initial: a block that warms from 18 °C to 48 °C has Δθ = 30 °C, not 48 °C.
Water has an unusually high specific heat capacity, about 4200 J/(kg °C) against roughly 900 for aluminium and 450 for steel. That single fact explains a great deal: water is used in central heating and car cooling systems because it carries a lot of energy per degree; coastal areas have milder winters than inland ones because the sea takes a long time to cool; and a hot water bottle stays warm far longer than a metal object of the same mass.
A high specific heat capacity means a substance is slow both to heat up and to cool down.
- c = ΔE ÷ (mΔθ)
- Specific heat capacity is the energy transferred per unit mass per degree of temperature change.c in J/(kg °C), ΔE in J, m in kg, Δθ in °C
- ΔE = mcΔθ
- The energy needed to change the temperature of a mass of a substance.ΔE in J, m in kg, c in J/(kg °C), Δθ in °C
Worth remembering
- c = ΔE ÷ (mΔθ), so ΔE = mcΔθ; c in J/(kg °C) or J/(g °C).
- Water: c ≈ 4200 J/(kg °C), much higher than most metals.
- High c means slow to warm and slow to cool.
Practical investigation
To measure the specific heat capacity of a metal, take a block of known mass with holes drilled for a heater and a thermometer. Record the starting temperature, switch on the electric heater for a measured time, and record the highest temperature reached.
The energy supplied is found from the electrical power and time: E = Pt, or E = VIt if you measure voltage and current, or read directly from a joulemeter. Then use c = ΔE ÷ (mΔθ). For a liquid the method is the same with the liquid in an insulated container, stirred so the temperature is even throughout; its mass is found by weighing the container empty and then full.
The result usually comes out too high, and knowing why is worth as many marks as the calculation. Some of the energy supplied warms the surroundings rather than the block, so the measured temperature rise is smaller than it should be for that energy, making c appear larger. Insulating the block, starting below room temperature and finishing the same amount above it, and taking the maximum temperature after switching off — since heat continues to spread through the block — all reduce the error.
Two other details: a drop of oil in the thermometer hole improves thermal contact, and the block should be left long enough for the temperature to even out before the final reading.
Worth remembering
- Supply a measured energy E = Pt, measure m and Δθ, then c = ΔE ÷ (mΔθ).
- Energy lost to the surroundings makes the measured c too high.
- Insulate, stir liquids, and read the maximum temperature after switching off.
Internal energy
When you heat an object, the energy goes into its particles. The total energy stored in all the particles of an object is called its internal energy. Whenever the temperature of an object rises, its internal energy has increased: a pan of water at 80 °C has more internal energy than the same pan of water at 20 °C, because energy had to be supplied to warm it up.
Internal energy also depends on how much material there is. A bath of water at 40 °C has far more internal energy than a cup of water at 40 °C, because it contains far more particles, even though the two are at the same temperature. That is why a spark at over 1000 °C can land on your skin harmlessly: its internal energy is tiny.
In terms of particles, a rise in temperature is an increase in the average kinetic energy of all the particles in the object. The particles always have a spread of speeds, some faster and some slower, but heating shifts the whole spread upwards, so their average kinetic energy goes up. Cooling does the reverse. Temperature therefore tells you about the average kinetic energy of the particles, while internal energy is the total energy of all of them together.
Worth remembering
- Internal energy is the total energy stored in the particles of an object.
- A rise in temperature means the internal energy of the object has increased.
- A rise in temperature is an increase in the average kinetic energy of all the particles.
Worked example
Heating 0.5 kg of water by 10 °C with c = 4200 J/(kg °C) requires 21 000 J.
Investigate scatter and systematic error
Change a value and watch the readings follow. Open it on the lab stage
Investigate scatter and systematic error
There is no zero offset, and the readings lie up to 0.484 cm from the best-fit line.
- Furthest point from the best-fit line
- 0.484 cm
- 3.13 cm − 2.646 cm at 1 s
- Best-fit intercept
- 1.165 cm
- 1 cm true + 0 cm offset + 0.165 cm random
- Best-fit gradient
- 1.965 cm/s
- (20.815 cm − 1.165 cm) ÷ 10 s
Goal
Find out how random scatter and a zero offset each change a set of readings, and which of them taking more repeats can fix.
Predict, where you are
If Ithe, thewill
Say what you expect before you move anything. Check makes the change for you.
Test, still to come
Change one thing at a time and watch the readings. The notebook keeps a reading each time you record one.
Explain, still to come
After you check a prediction, this says why it happened.
Try this · 0 of 3
- Turn the random scatter up to 1.5 cm with no zero offset. Does the best-fit line still follow the true line?, not yet
- Set a zero offset of −1 cm with no scatter. How far does every reading move?, not yet
- With 1 cm of scatter and a 1 cm zero offset, take 10 repeats at each time. Which error does averaging reduce, and which does it leave?, not yet
reading = true value + zero offset + random error
at 5 s: 11 cm + 0 cm − 0.229 cm = 10.771 cm
Investigation notebook · 0 readings
Change one variable at a time and record the results. These readings stay here until you leave this lesson or reset the notebook.
About this model
Made-up readings of a distance that truly grows as 2 cm/s × time + 1 cm. Each reading’s random error comes from a fixed set drawn once, up to the scatter either side, so the same settings always give the same readings. The best-fit line is the least-squares straight line through the plotted points.
Practice
Warm-up · not marked
Check your understanding
Answer in your own words, then compare with the worked answer. Nothing here is saved or scored.
Worked answer
c = 9000/(2 × 10) = 450 J/(kg °C).
Check your method, units and explanation against it.
Marked practice
Set 1 of 5 · easiest first · Checked as you go, with the worked answer. Sign in or create a free account to save your progress.