Electrical Quantities · Cambridge syllabus 4.2 · Lesson 6 of 6
Electrical Energy and Power
A circuit transfers energy from a source, such as a cell or the mains supply, to its components, and from them to the surroundings. Electrical power is the rate of that transfer: P = IV, current times potential difference. The energy transferred in a time t is E = IVt. Electricity is sold by the kilowatt-hour, the energy a 1 kW appliance transfers in one hour.
By the end, you can
- Understand that electric circuits transfer energy from a source, such as a cell or the mains supply, to the components and then to the surroundings.
- Recall and use P = IV.
- Recall and use E = IVt.
- Define the kilowatt-hour (kW h) as a unit of energy.
- Calculate the cost of using electrical appliances where the energy unit is the kW h.
Energy in circuits
Every electric circuit does the same basic job: it transfers energy. The source, such as a cell, a battery or the mains supply, provides the energy; the current carries it along the wires to the components; and the components pass it on to the surroundings. In a torch, energy from the chemical store of the battery is transferred electrically to the lamp, which transfers it to the surroundings by light and by heating.
The same pattern fits every appliance. An electric kettle transfers energy from the mains to the thermal store of the water. A fan’s motor gives its blades a kinetic store, and the moving blades then pass the energy to the air, ending up as heating and sound. A phone charger fills the chemical store of the phone’s battery, which the phone later empties as light, sound and heating. However useful the energy was along the way, almost all of it ends up warming the surroundings.
No energy is created or destroyed on the way. The components transfer exactly as much energy as the source supplies, which is why a cell eventually goes flat: its chemical store has been used up. The charge is not used up at all; it carries energy from the source to the components and returns to the source for more.
Worth remembering
- A circuit transfers energy from the source to the components, and then to the surroundings.
- The charge carries the energy round; it is not used up.
- Almost all the energy ends up heating the surroundings.
Electrical power
Power is the rate at which energy is transferred, measured in watts, W; one watt is one joule per second. For an electrical component, the power depends on two things you can measure: the current through it and the potential difference across it. Power = current × potential difference, or P = IV.
It makes sense that both matter. The p.d. tells you how much energy each unit of charge transfers as it passes through the component, and the current tells you how much charge flows through it. A larger p.d. with the same current, or a larger current with the same p.d., means more energy is transferred every second. A lamp with 6.0 V across it and a current of 2.0 A through it has a power of 2.0 × 6.0 = 12 W: it transfers 12 J of energy every second.
A kettle on a 230 V supply taking a current of 13 A has a power of 13 × 230 = 2990 W, about 3 kW. Rearranged, I = P ÷ V, so a 60 W lamp on 230 V takes a current of 60 ÷ 230 = 0.26 A; this is how the current for choosing a fuse is worked out. And V = P ÷ I, so a 24 W motor that takes 2.0 A needs a p.d. of 24 ÷ 2.0 = 12 V. The power of an appliance is printed on its rating plate.
- P = IV
- Electrical power is the current multiplied by the potential difference.P in W, I in A, V in V. Rearranged: I = P ÷ V and V = P ÷ I.
Worth remembering
- Power is the rate of energy transfer, measured in watts: 1 W = 1 J/s.
- P = IV. Rearranged, I = P ÷ V and V = P ÷ I.
- Doubling either the current or the p.d. doubles the power.
Electrical energy
The total energy an appliance transfers is its power multiplied by the time it is on for. Since the power is IV, the energy is E = IVt, with E in joules, I in amperes, V in volts and t in seconds.
A kettle takes a current of 5.0 A from a 230 V supply for 3.0 minutes. The time must be in seconds: 3.0 minutes is 180 s, so E = 5.0 × 230 × 180 = 207 000 J, about 210 kJ. Multiplying by 3 instead of 180 gives an answer 60 times too small, which is the commonest mistake with this equation.
A phone charger supplying 2.0 A at 5.0 V for one hour, 3600 s, transfers 2.0 × 5.0 × 3600 = 36 000 J. So three minutes of the kettle transfers nearly six times as much energy as an hour of charging, because the kettle’s power is so much greater. The equation can be rearranged to find any one quantity: a 12 V heater that transfers 7200 J in 60 s takes a current of 7200 ÷ (12 × 60) = 10 A.
- E = IVt
- The energy transferred is the current times the potential difference times the time.E in J, I in A, V in V, t in s.
Worth remembering
- E = IVt, the energy in joules, with the time in seconds.
- Convert minutes and hours to seconds before multiplying.
- Energy transferred = power × time.
The kilowatt-hour
The joule is far too small a unit for a household’s energy use, so electricity is sold in kilowatt-hours, written kW h. One kilowatt-hour is the energy transferred by a 1 kW appliance in 1 hour. In joules that is 1000 W × 3600 s = 3 600 000 J, so 1 kW h = 3.6 MJ. A kilowatt-hour is an amount of energy, not a power: kilowatts tell you how fast energy is transferred, kilowatt-hours tell you how much.
To find the energy in kW h, multiply the power in kilowatts by the time in hours. A 2.5 kW heater on for 4.0 hours transfers 2.5 × 4.0 = 10 kW h. Convert first: a 100 W lamp is 0.1 kW, and 30 minutes is 0.5 h, not 0.3 h. Left on for a week, 168 hours, that lamp transfers 0.1 × 168 = 16.8 kW h, more than the heater, which shows how a low-power appliance left on for a long time can use more energy than a powerful one used briefly.
The cost is the energy in kW h multiplied by the price of one kW h. At 28 cents per kW h, the heater’s 10 kW h costs 10 × 28 = 280 cents, or $2.80. An electricity meter counts kilowatt-hours: if it reads 2786 kW h at the start of a month and 3054 kW h at the end, the household used 3054 − 2786 = 268 kW h, which at 25 cents per kW h costs 268 × 25 = 6700 cents, or $67.00.
- 1 kW h = 3.6 MJ
- One kilowatt-hour is the energy a 1 kW appliance transfers in one hour.1 kW h = 1000 W × 3600 s = 3 600 000 J
- energy (kW h) = power (kW) × time (h)
- The energy in kilowatt-hours is the power in kilowatts multiplied by the time in hours.
- cost = energy (kW h) × price per kW h
- The cost of using an appliance is the number of kilowatt-hours times the price of each one.
Worth remembering
- One kilowatt-hour is the energy a 1 kW appliance transfers in 1 hour: 1 kW h = 3.6 MJ.
- Energy in kW h = power in kW × time in hours.
- Cost = energy in kW h × price per kW h.
- A kilowatt-hour is a unit of energy, not of power.
Worked example
A 2.0 kW heater is on for 3.0 hours. Energy = 2.0 kW × 3.0 h = 6.0 kW h. At 30 cents per kW h, the cost is 6.0 × 30 = 180 cents, which is $1.80.
Build a circuit
Free for everyone, on its own page.
Practice
Warm-up · not marked
Check your understanding
Answer in your own words, then compare with the worked answer. Nothing here is saved or scored.
Worked answer
P = IV = 0.25 × 230 = 57.5 W. E = IVt = 0.25 × 230 × 120 = 6900 J.
Check your method, units and explanation against it.
Marked practice
Set 1 of 4 · easiest first · Checked as you go, with the worked answer. Sign in or create a free account to save your progress.