Electrical Quantities · Cambridge syllabus 4.2 · Lesson 3 of 6
Potential Difference and EMF
Includes Supplement objectivesPotential difference is the work done by a unit charge passing through a component. E.m.f. is the electrical work done by a source in moving a unit charge around a complete circuit. Both are measured in volts, where 1 V = 1 J/C. Connect a voltmeter in parallel with the component.
By the end, you can
- Define potential difference as the work done by a unit charge passing through a component, measured in volts.
- Recall and use V = W ÷ Q. [Supplement]
- Use analogue and digital voltmeters with different ranges.
- Define e.m.f. as the electrical work done by a source in moving a unit charge around a complete circuit, measured in volts.
- Distinguish EMF from potential difference.
- Recall and use E = W ÷ Q. [Supplement]
- Know that the sum of the p.d.s across the components in a series circuit equals the e.m.f. of the source. [Supplement]
Potential difference
Potential difference, p.d., often called voltage, measures how much energy the charge transfers as it passes through a component. It is defined as the work done by a unit charge passing through the component, and it is measured in volts, V. Work done means energy transferred, so the larger the p.d. across a lamp, the more energy each unit of charge gives it, as light and by heating. A lamp with 12 V across it transfers twice as much energy for each unit of charge as one with 6 V across it.
As an equation, V = W ÷ Q, where W is the work done, the energy transferred, in joules, and Q is the charge in coulombs. One volt is one joule per coulomb. If 690 J is transferred as 30 C of charge passes through a heater, the p.d. across it is 690 ÷ 30 = 23 V. Rearranged, W = QV, so 5 C passing through a 12 V lamp transfers 5 × 12 = 60 J.
Potential difference is measured with a voltmeter, connected in parallel as a loop across the component, because it compares the two points on either side of it. A voltmeter has a very high resistance, so almost no current is diverted through it and the circuit is barely disturbed. Voltmeters, like ammeters, are analogue, with a needle and a scale, or digital, and many have several ranges, such as 0–2 V, 0–20 V and 0–200 V. Choose the smallest range the p.d. will not exceed, work out the value of one small division before reading an analogue scale, and read the needle from directly in front. Series for an ammeter, parallel for a voltmeter, is worth committing to memory.
- V = W ÷ Q
- Potential difference is the work done per unit charge passing through a component.V in V, W in J, Q in C. Rearranged: W = QV.
Worth remembering
- P.d. is the work done by a unit charge passing through a component, measured in volts (V).
- V = W ÷ Q, so 1 V = 1 J/C.
- A voltmeter goes in parallel, across the component, and has a very high resistance.
- On any meter, choose the smallest range the reading will not exceed.
EMF
Electromotive force, or e.m.f., describes the source rather than a component. It is defined as the electrical work done by a source, such as a cell, a battery or a generator, in moving a unit charge around a complete circuit, and it is measured in volts, like p.d. The larger the e.m.f., the more energy the source gives to each unit of charge it drives round. Despite the name, e.m.f. is not a force.
The difference between the two is the direction of the energy transfer. E.m.f. describes a source putting energy into the charge as it drives it round the whole circuit; potential difference describes a component taking energy out of the charge as it passes through. Every bit of energy the source gives the charge is transferred by the components, which is conservation of energy stated for circuits. A lamp lights because the cell does work on the charge and the lamp transfers that energy as light and by heating. It follows that in a series circuit the p.d.s across the components add up to the e.m.f. of the source: if a 9.0 V battery drives a current through two lamps in series and one has 4.0 V across it, the other has 5.0 V across it.
As an equation, E = W ÷ Q, where W is the work done by the source in joules and Q is the charge it moves round the circuit in coulombs. A battery that does 270 J of work moving 30 C round a circuit has an e.m.f. of 270 ÷ 30 = 9.0 V. Rearranged, W = QE, so a 6.0 V supply moving 50 C does 6.0 × 50 = 300 J of work.
- E = W ÷ Q
- E.m.f. is the work done by a source per unit charge moved around a complete circuit.E in V, W in J, Q in C. Rearranged: W = QE.
Worth remembering
- E.m.f. is the electrical work done by a source moving a unit charge round a complete circuit, in volts.
- E.m.f.: energy given to the charge by a source. P.d.: energy taken from the charge by a component.
- E = W ÷ Q, the same form as V = W ÷ Q.
- In a series circuit the p.d.s across the components add up to the e.m.f.
Worked example
A 6 V source supplies 6 J to each coulomb. If 3 C passes, it supplies 18 J.
Energy per coulomb
Part of the full Physics course. This unit’s free simulation is Build a circuit.
Practice
Warm-up · not marked
Check your understanding
Answer in your own words, then compare with the worked answer. Nothing here is saved or scored.
Worked answer
V = W/Q = 24/4 = 6 V.
Check your method, units and explanation against it.
Marked practice
Set 1 of 5 · easiest first · Checked as you go, with the worked answer. Sign in or create a free account to save your progress.